5/14/2019
Posted by admin
Polaris Pb4 Booster Pump Wiring Diagram Average ratng: 8,8/10 8294 reviews
The Polaris Booster Pump supplies high pressure
water to the Polaris pool cleaner. It is not self-
filtration pump is also running. Running the
This is a image galleries about Pb4 Booster Pump Repair.You can also find other images like wiring diagram, parts diagram, replacement parts, electrical diagram, repair manuals, engine diagram, engine scheme, wiring harness, fuse box, vacuum diagram, timing belt, timing chain, brakes diagram, transmission diagram, and. Mar 16, 2018 - polaris booster pump wiring instructions motor replacement wire diagram installation,polaris pb4 booster pump wiring diagram installation.
damage the booster pump. Improper operation
Important Safety Instructions
When installing and using this electrical
always be followed.
2. WARNING — To reduce the risk of injury, do
they are closely supervised at all times.
permanently installed pools and may also be
not use with storable pools. A permanently
ground or in a building such that it cannot be
pool is constructed so that it may be readily
its original integrity.
Booster Pump should always be
5. A solid copper bonding conductor not smaller
connected from the accessible wire connector
pool, spa or hot tub structure and to all
piping within 5 ft (1.5 m) of the inside walls of a
is installed within 5 ft of the inside walls of the
6. SAVE THESE INSTRUCTIONS.
Note: Plumb the booster pump up-
From
Filtration Pump
2
Heater
The motor comes wired for 240 volts. The booster
volts. To rewire, follow the instructions on the
the 'sizing' plate on the side of the motor.
A separate time clock (in addition to the filtration
the 'On' and 'Off' functions of the booster pump.
If a time clock is used, it should be set to turn on
filtration pump is turned on and turn off the
cleaner at least one half hour before the filtration
pump shuts off. The Polaris will clean the pool in
and the amount of debris. Periodically check the
time clock settings to make sure they are properly
Installation with a Heater
If the filtration system has a heater, the booster
no closer than three feet downstream from the
diagram). DO NOT TAP THE BOOSTER PUMP
HEAT SINK PIPE THAT COMES DIRECTLY OUT
Installation with a Solar System
always in the water flow (see the diagram below).
the entire water flow at certain times. Care must
'NON-FLOW' pipe when the solar heating system
the system. This override will shut the booster
Minimum
Plumbing
Options
1, 2 or 3
Spa
Pump
To
Chlorinator
Advertisement
Also See for Polaris PB4-60
Polaris PB4-60 Installation And Operation Manual40 pages
Zodiac Pb4 60 Polaris Booster Pump
Related Manuals for Polaris PB4-60
Summary of Contents for Polaris PB4-60
Page 1: Important Safety Instructions
Polaris Booster Pump Installation Instructions The Polaris Booster Pump supplies high pressure Electrical Hook-up water to the Polaris pool cleaner. It is not self- The motor comes wired for 240 volts. The booster priming and should not be running unless the pump motor may be wired for either 120 or 240 filtration pump is also running.- Page 2 If the Polaris will not run or runs slowly Checking Water Flow while the solar heating system is on, contact our Once the system is plumbed, it is important to Customer Service Department. verify that there is sufficient water flow to the booster pump.
- Page 3 Softube quick connects (part #P133) and optimum level of efficiency. one six-foot section of flexible reinforced hose If the Polaris cleaner does not have UWF (part #P19). pressure restrictors, the UWF restrictor kit (part Universal Wall Fitting Restrictor Kit #10-108-00) is available separately through your participating Polaris dealer.
Page 4: Limited Warranty
Polaris Pool Systems warrants the PB4-60 Booster Pump it manufactures, including all parts and components thereof, to be free of defects in material and workmanship. If you have a question regarding your Polaris Booster Pump, please feel free to call or write us. Be sure to include the serial number of your unit.